Welcome to FJR’s Monster Build

This plug can be built with basic hand tools for those of you that don’t have power equipment. You can use screw eyes instead of thru wire. Stick on eyes or paint your own eyes and the lip slot can be done with a hand saw. You could even use a hand drill for the belly weight.

Step 1 - The type of wood you use is important, as this is a large plug and weight is a factor. Pine would be a good chose to try for the first one, as it is easy to work with. For this build I will be using Cedar ( don’t know what kind ), when finished this plug will be 8 3/4" long and weight between 2.25 & 2.50 oz.

I start by selecting a template that I made from a design I first did on paper. The challenge here is to come up with a design of your own and make it work. I have a number of sizes and variations that I use.
[You must be registered and logged in to see this image.]

Then I trace out the pattern on the piece of cedar.
[You must be registered and logged in to see this image.]

Step 2 - Next I cut it out on a band saw and do the lip slot while it’s still flat. For those of you that don’t have a band saw, you can use a scroll saw, jig saw or even a coping saw.
[You must be registered and logged in to see this image.]

Step 3 - To shape the plug I use two methods, depends on what mood I’m in lol. For this demo I will use the method that was shown to me by Alphabaits (Ted) where you use a 1"strip of sand paper cut from a belt sander. I start out with 50 grit to get the basic shape then switch to 80 grit to smooth things out.

The other method is to use a rasp, takes longer, by you don’t get all the dust like with the sanding method.
[You must be registered and logged in to see this image.]

Place the cut out blank in the vise and start sanding, as my grandson says, like you were drying your back after a nice hot shower. I always start with the top first and then the bottom and finish off the sides. An option here would be to leave the sides flat, I like to round them off, the choice is yours.

If you chose the rasp method, doesn’t matter where you start, just as long as it’s the corners and do a little at a time constantly turning the plug as you go.

One thing I advise to do, if sanding, is to wear a dust mask and as you can see in the photo, I have my shop vac set up under the plug to help keep the dust down. Unless of course you enjoy breathing and choking on wood dust.
[You must be registered and logged in to see this image.]

The next photo shows how the plug looks half way done. Flip it over and finish it off. I have a set of plastic jaws, same as Alphabaits uses, to keep from damaging the plug in the vise.
[You must be registered and logged in to see this image.]

Step 4 - After the plug is shaped I then hand sand it with either a block of wood and sandpaper or with a sanding sponge, sometimes I use both. This is to even everything out, as there will be high and low spots.
[You must be registered and logged in to see this image.]

Step 5 - Next I drill the thru hole, if you plan on using screw eyes skip this step. I have a board with a dowel center in it and I line it up with a steel rod that is inserted in the chuck. ( Thanks to Roccus )
[You must be registered and logged in to see this image.]

First I drill the nose then I flip it over and drill the tail. I finish it off with a hand drill. Next I do the belly, weight hole and the eyes. The size of these holes is up to you, it will depend on what size weight you use, whether you decide to make a sealed plug or use swivels and what size eyes. All choices you’ll need to make. On this plug I’m using 23/64 th for the hook hangers, 15/32 nd for the belly weight and 7/16 th for the eyes.
[You must be registered and logged in to see this image.]
[You must be registered and logged in to see this image.]



Step 6 - A little finish sanding, rounding off all edges and onto the sealer. I use a 50/50 mixture of spar and mineral spirits. Normally it takes three dips, allowing it to fully dry in-between coats, to get it the way I like.
[You must be registered and logged in to see this image.]


Step 7 - After the sealer has had time to dry I then assemble the plug and fill all the cavities with two part epoxy to create a fully sealed plug. After the epoxy has dried I sand everything smooth and apply a coat of min wax sanding sealer, really locks everything in nicely.
[You must be registered and logged in to see this image.]

wow. nice sweet step by step. I might have to try one of those

Step 8 - Now that all the hard stuff is done it’s time to paint. This is where you can let your creative juices flow. Since I don’t have any artistic ability I will keep it simple. For lack of a better term I will call this a bunker pattern.

First a light sanding then a primer. I normally use Rustoleum spray primer.
[You must be registered and logged in to see this image.]

I then apply a coat of silver pearl.
[You must be registered and logged in to see this image.]

Follow that up with gold pearl on the top and shoulders.
[You must be registered and logged in to see this image.]

On this pattern I chose to use pearl green for the top. This is where you can get creative if you want, 49er fans could use red, Saints fans, black or some other shade of green or blue. I have come up with some nice shades of green by mixing colors. Play around, that’s what makes it fun.
[You must be registered and logged in to see this image.]

wow frank awsome tutorial ....u make it look easy but i know it isnt.....

big fan of your work u know that....work is truely art ......

I finish it off with a light shade of purple, that is a mix of silver pearl and purple pearl, under the eyes and add some dots along the body. At this point I give it a light coat of clear acrylic.
[You must be registered and logged in to see this image.]


After it has dried give it a coat of your favorite top coat. I like E-Trex the best and usually give it two coats. I find Devcon dries to fast for me to completely cover this size plug, I will use it on smaller freshwater plugs as I do like the way it comes out. The choice is yours, there is no right or wrong.

There you have it, looks pretty good with out being too complicated.
[You must be registered and logged in to see this image.]


I want to say thanks to Smitty for providing this fun site, Skippy for inviting me to do this build, Ted for showing me how and Keith for the painting lessons along with loads of plug theory.

I enjoyed presenting this build and I hope everyone got at least something from this build. Good luck to anyone that tries it.

One last thing, don’t forget the Saturday night chat at 10 pm, where this plug will be raffled off. See you there.

Excellent tutorial FJR. You do make it look easy but it ain't like Steve said.

Nice work Frank!
Very informative, I'm going to have my son read and re-read this a couple of times. I'd still like to arrange a date for me to bring him by to see how it's really done since me teaching him is like the blind leading the blind.